Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you’re towing, knowing exactly when your towed car’s brakes are applied gives peace of mind and prevents costly mistakes. The Roadmaster Stop Light Switch Kit wires directly into the towed car’s fuse box to send a 12-volt signal to your RV’s monitoring system every time the brake pedal is pressed. Unlike systems that only detect when the air cylinder moves, this setup shows what’s really happening with the pedal itself, so you always know your brakes are working the way they should.
If a supplemental braking system is not positioned correctly, it can keep constant pressure on the pedal, wearing down tires or causing brake damage without you realizing it. This stop light switch kit helps prevent that by confirming each actual pedal press—no guessing, no relying on indirect feedback. You’ll know right away if something’s off, before small problems become expensive fixes.
Some vehicles don’t have an ignition setting that keeps the brake lights active during towing. This kit solves that problem by providing its own dedicated signal to the braking system and the RV monitor. That means your setup stays safe and fully functional even when your ignition is off, so you can tow confidently without worrying about losing your brake light signal.
Flat towing can be a much more convenient way to take your car RVing with you than using a trailer or a tow dolly. It'll save you storage space both at home and at the campsite, and it takes less time and hassle to hook up.
To flat tow your vehicle, there are 5 basic components you're going to need: a tow bar, a base plate kit, a safety cable set, tow bar wiring, and a flat tow braking system.
| For the RV | Between the RV and Towed Car | For the Towed Car |
|---|---|---|
| Hitch | Tow bar | Base plate |
| Wiring plug | Safety cables | Braking system |
| Wiring adapter cord | Wiring kit/diodes |
The custom-fit base plate installs on the frame of your toad so you can connect the car to your RV with a tow bar. Hook up safety cables between the vehicles to ensure that the toad does not separate from the motorhome if the tow bar becomes detached. Tow bar wiring syncs your vehicle's signal lights with your motorhome's tail lights, as required by law in most states. Finally, the flat tow braking system - also required in most states - activates the brakes in the toad when you hit the brakes in the RV, making for smoother, safer braking, and preventing wear on your motorhome.
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
Ratings & Reviews
This is the second switch I’ve bought. The fuse holder could be designed a little better. Perhaps with the wire out the top rather than the side.
The instructions are a little difficult to follow but it was easy to install
Easy installation. I had an issue getting the kit ordered, but the customer service agent was phenomenal in her assistance getting it resolved.
It works as designed. Tricky for this old fat guy to work under the jeep dash but eventually got it installed and adjusted.
Works great fairly easy install. It has been in use for the last 8 month's with no issues. Here may be some helpful hints that I found when installing. Use 10-12" long extension for 13mm nut (left side of opening panel that was removed). Install bracket. Adjust plunger & backing nut by feel. Remove bracket. Install switch with ring washer & nut. Crimp red & green wires on switch wires. Reinstall bracket under dash.
Was disappointed that your site said this was the part I needed so I ordered it. Then realized it was not correct part. Called next day to cancel and Oder correct part. I was told I could not cancel it and would have to pay to ship it back. The correct part which was ordered second came 2 days before first part. To get a refund I still had to pay to ship it back. Other than this trailer has been good to work with and quality parts.
Thank you, order arrived as promised, and install was easy and fit my 2025 Jeep Grand Cherokee Overland perfect to operate my brake light on my Motorhome dash.
It is my opinion that the universal brake light switch is the easy way to go. Hardest part doing the DIY way is the place you are working in. I.have a few sore spots trying to get underneath the steering wheel. The benefit is you have instant info that the switch works. A light comes on when you push the break pedal
I have a ‘23 Bronco with the Lux package. The Bronco had a factory brake switch in the spot this thing would go. Advice was unclear whether I could use a factory wire to install my brake controller. I went with the wire that lit the test light when brakes were pressed (key on). I think it was violet with a stripe at the plug for a factory Brake controller. I don’t have the factory tow package. Seems to work but not yet tested with a trailer. Only 3 stars because of the uncertainty. I’ll use this switch on a different project.
Product works great...But was shorted the female connector to terminal 1...Cost over 5 dollars at Auto Zone.As no one sells just one.....Its in the picture...Not in my parts bag...But a perfect fit on the brake switch mount .Three stars only because I had to go buy a connector to complete the job.
I installed the item in my 2024 Bronco to support braking indication in the motorhome while being towed, since Ford does not include one these days. As far as I can tell, this is the only commercially available kit to avoid cobbling up your own design. It is tedious to install mechanically and, especially tedious to adjust transverse mount position and depth of travel. The button on the switch is too small, requiring very precise alignment to the brake pedal arm (approx 1/4" wide) in the transverse direction from the switch movement. There is no screw type adjustment in that direction so bracket bending/and or bracket mounting spacers is required. I am also afraid the switch button being small and made of some type of poly, it will slip sideways, deform, or wear with even the slightest offset and begin to push the bracket aside. However, it has worked in a few thousand miles of towing behind a motorhome so far. I will keep an eye on this and test function whenever hooking up to tow (a normal practice anyway). I kept thinking it would be easier to use a long lever low force microswitch instead of a tiny soft-tipped, rather hard spring or drag, pushbutton, which would require its own mounting design. Maybe a small highly adjustable ball clamp mount work with a microswitch as well. But I must resist my engineering background tendencies in exchange for getting the job done! Sorry for the quality of the photos. It is in a difficult place for phone camera.
Thanks everyone at etrailer for your help and quick response and shipping! My project turned out really great as you can see in the pictures I have included. The plug for the removable holders I 3D printed. Thanks Fred
Came in clutch with having the product in stock and the fact that est. delivery was 5/27 and it was delivered 5/22. Couldn't have had a better experience.
Pit this in my 2025 Maverick not much room to work but I got it installed, happy with the product.
This switch bracket is not what I expected. It doesn’t appear to be strong enough to keep the switch adjusted properly. I’ve installed it, so we’ll see if it stays adjusted like it should.
Roadmaster products are great, very pleased with the superb instructions. Very difficult to mount the pulley for the invisibrake in my Ford Maverick. Trying to drill stainless steel behind the brake pedal was near impossible. Could a bracket for the pulley be mounted on the same studs as the Stop Light Switch?
Do you have a question about this Flat Tow Brake System?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Kate F.
12/17/2025
I wish you could mount it there Donald, but those stop-light-switch studs are only designed to hold the switch bracket. Adding the pulley bracket changes the spacing and alignment, which can make the brake lights stay on, not come on, or throw off the Invisibrake’s operation. The studs also aren’t meant to handle the side-load from the cable, so Roadmaster doesn’t recommend using them. For drilling stainless, the trick is a cobalt bit (M35 or M42), slow speed, steady pressure, and cutting oil so the metal doesn’t work-harden. Are you new to flat towing, or just getting a different vehicle set-up?